|
 |
|
For further
Universal Insert details....... |
 |
Universal
insert and clip
Part Ref.
6316
Designed to accommodate the
following mould connections; Turbo Autosprue, PV Sensor Insert
Adaptor, 10mm Injection Adaptor,10mm Vacuum Adaptor, 6mm Vacuum
Connection, 3/4" Vacuum Connection Adaptor, Vacuum Catchpot and
Blank Plug.
|
 |
10mm resin feed connection
adaptor for universal insert. Part Ref. 6319
Designed to connect 10mm
injection pipe to the mould via the universal insert bonded in
during mould manufacture on the resin flow channel.
6mm resin feed connection
adaptor for universal insert
Part Ref. 6319-6mm
Can also be used as a 6mm
venting point.
|
|
10mm Vacuum
Connection Adaptor for universal insert.
Part Ref.
6318
Designed to connect a 10mm
flange vacuum line to the mould. The universal insert bonds into
either the upper or lower half of the mould to accommodate this
adaptor.
|
 |
Part Ref. 6315
Designed to connect either a
Geka or 3/4" Vacuum line to the mould via the universal insert.
|
 |
 |
Part Ref.
6328
Blank plug for universal
insert, for use when the insert is not in use it can simply be
blanked off.
|
 |
Direct Resin Vacuum Catchpot
Part ref. 2146
Aluminium vacuum lid as
standard. Additional/alternative view lids available (as shown).
Provides secure LRTM mould final resin fill reservoir. Stainless
steel body with locked and sealed tapered fittings allows instant
disconnection after cure. Large multi channel Catchpots also
available. Can be used with the universal insert if part numbers
2146-VIEW UNI or 2146-UNI are used.
|
|
Reusable Wing Seal channel profile
Part ref. 3391
Provides rapid
calibration 26 x 13mm groove when making mould Wing seal channel. We
recommend using “super glue” adhesive to fix to 1mm flange wax.
Designed to take the mould vacuum seal wing profile.
Supplied in
25m coils
|
 |
Mould Vacuum Seal Wing Profile
Part ref.
1680
A well
proven secondary neoprene seal (Outer) for all LRTM moulds. Easy to
apply, join and seal. Fits 26 x 13mm groove for optimum performance.
Mould Vacuum
Seal Wing Profile
Part Ref.
5895
As above
but silicone material.
Supplied in 25m coils
|
 |
|
Dynamic Silicone Seal
Part ref.
1114
For a professional LRTM mould the Dynamic seal offers many
advantages over Static Mushroom seal above. Features: adjustable
sealing pressure, safer mould opening, seals on vertical draft
face and self-adjusting around difficult flange profiles.
Supplied in 25m coils
|
|
Reusable Red Dynamic Seal channel profile
Part ref.
3340
Provides rapid
calibration profile when making mould Dynamic seal channel. We
recommend using “super glue” adhesive to fix to 1mm flange wax.
Supplied in 25m coils
|
|
Dynamic Seal Installation Kit
Part ref.
2056
Primarily used in conjunction with new installations of Dynamic
seal #1114 above. The kit includes: seal mould insert, nylon
connection tube, nylon connection tube former and silicone
jointing tube. Complete with instructions for use.
|
|
V section seal
Part Ref. 6439
This is an
alternative to the dynamic seal. It is designed to fit all
moulds which have been made with the dynamic seal channel
profile. This seal is robust and offers a smaller seal contact
area with the mould flange providing good seal efficiency even
when a mould flange has gelcoat applied during production.
Supplied in 25m coils
|
|
|
Mushroom LRTM Seal Green Silicone
Part ref.
3202
The first
choice for a Primary resin seal (Inner), this highly resilient
silicone gives a long moulding cycle life. Fits 10 x 5mm groove.
Designed for 1mm seal compression.
Supplied in 25m coils
|
|
Reusable Mushroom Seal Channel Profile 10mm x 5mm
Part ref.
0002
Ideal
profile for rapid and accurate forming of the groove profile
during mould build to take the Mushroom seal # 3202.
Supplied in 25m coils
|
|
Reusable
Resin Flow Channel Profile.
Part Ref.
4530
Designed for rapid calibration
of the resin flow channel during the mould manufacture.
Supplied in 25m coils
|
|
Small
Reusable Resin Flow Channel Profile
Part Ref.
6438
As above but approximately
1/3 the cross section. Designed for small moulds upto 1m2
approximately 4m of resin channel.
Supplied in 25m coils
|
|
|
Latch Clamp
Part ref. 3370
To assist initial
closure of peripheral vacuum seal. Can be screwed to mould edge
wooden frame or welded to steel frame. Complete with drawing showing
set up.
|
|
Air
Ejector valve.
Part ref. 0580
The unit is designed to be moulded flush with mould face. In
operation it retracts the face
and simultaneously forces compressed
ejection air between the mould and moulded part.
Air Ejector control switch.
Part ref. 1949
Air
Ejector control switch including fittings and pipe.
|
Print friendly version