 |
Universal insert and clip Part Ref. 6316 Designed to accommodate the following mould connections; Turbo Autosprue, PV Sensor Insert Adaptor, 10mm Injection Adaptor,10mm Vacuum Adaptor, 6mm Vacuum Connection, 3/4" Vacuum Connection Adaptor, Vacuum Catchpot and Blank Plug. |
 |
10mm resin feed connection adaptor for universal insert. Part Ref. 6319 Designed to connect 10mm injection pipe to the mould via the universal insert bonded in during mould manufacture on the resin flow channel. 6mm resin feed connection adaptor for universal insert Part Ref. 6319-6mm Can also be used as a 6mm venting point. |
|
10mm Vacuum
Connection Adaptor for universal insert.
Part Ref.
6318
Designed to connect a 10mm
flange vacuum line to the mould. The universal insert bonds into
either the upper or lower half of the mould to accommodate this
adaptor.
|
 |
Part Ref. 6315
Designed to connect either a
Geka or 3/4" Vacuum line to the mould via the universal insert.
|
 |
 |
Part Ref.
6328
Blank plug for universal
insert, for use when the insert is not in use it can simply be
blanked off.
|
 |
Direct Resin Vacuum Catchpot Part ref. 2146 Aluminium vacuum lid as standard. Additional/alternative view lids available (as shown). Provides secure LRTM mould final resin fill reservoir. Stainless steel body with locked and sealed tapered fittings allows instant disconnection after cure. Large multi channel Catchpots also available. Can be used with the universal insert if part numbers 2146-VIEW UNI or 2146-UNI are used. |
|
Reusable Wing Seal channel profile
Part ref. 3391
Provides rapid
calibration 26 x 13mm groove when making mould Wing seal channel. We
recommend using “super glue” adhesive to fix to 1mm flange wax.
Designed to take the mould vacuum seal wing profile.
Supplied in
25m coils
|
|
Mould Vacuum Seal Wing Profile
Part ref.
1680
A well
proven secondary neoprene seal (Outer) for all LRTM moulds. Easy to
apply, join and seal. Fits 26 x 13mm groove for optimum performance.
Mould Vacuum
Seal Wing Profile
Part Ref.
5895
As above
but silicone material.
Supplied in 25m coils
|
|
|
Dynamic Silicone Seal
Part ref.
1114
For a professional LRTM mould the Dynamic seal offers many
advantages over Static Mushroom seal above. Features: adjustable
sealing pressure, safer mould opening, seals on vertical draft
face and self-adjusting around difficult flange profiles.
Supplied in 25m coils
|
|
Reusable Red Dynamic Seal channel profile Part ref. 3340 Provides rapid calibration profile when making mould Dynamic seal channel. We recommend using “super glue” adhesive to fix to 1mm flange wax. Supplied in 25m coils |
| Dynamic Seal Installation Kit Part ref. 2056 Primarily used in conjunction with new installations of Dynamic seal #1114 above. The kit includes: seal mould insert, nylon connection tube, nylon connection tube former and silicone jointing tube. Complete with instructions for use. |
|
V section seal Part Ref. 6439 This is an alternative to the dynamic seal. It is designed to fit all moulds which have been made with the dynamic seal channel profile. This seal is robust and offers a smaller seal contact area with the mould flange providing good seal efficiency even when a mould flange has gelcoat applied during production. Supplied in 25m coils |
|
|
Mushroom LRTM Seal Green Silicone Part ref. 3202 The first choice for a Primary resin seal (Inner), this highly resilient silicone gives a long moulding cycle life. Fits 10 x 5mm groove. Designed for 1mm seal compression. Supplied in 25m coils |
|
Reusable Mushroom Seal Channel Profile 10mm x 5mm Part ref. 0002 Ideal profile for rapid and accurate forming of the groove profile during mould build to take the Mushroom seal # 3202. Supplied in 25m coils |
| Reusable Resin Flow Channel Profile. Part Ref. 4530 Designed for rapid calibration of the resin flow channel during the mould manufacture. Supplied in 25m coils |
|
Small Reusable Resin Flow Channel Profile Part Ref. 6438 As above but approximately 1/3 the cross section. Designed for small moulds upto 1m2 approximately 4m of resin channel. Supplied in 25m coils |
|
|
Latch Clamp Part ref. 3370 To assist initial closure of peripheral vacuum seal. Can be screwed to mould edge wooden frame or welded to steel frame. Complete with drawing showing set up. |
|
Air Ejector valve. Part ref. 0580 The unit is designed to be moulded flush with mould face. In operation it retracts the face and simultaneously forces compressed ejection air between the mould and moulded part. Air Ejector control switch. Part ref. 1949 Air Ejector control switch including fittings and pipe. |
